Home › Blog › Hi-WAX 100P Alternative

Hi-WAX 100P & A-C 8A Alternative: HY-1000 Polyethylene Wax Compared

Name: HY-1000 Polyethylene Wax
Brand: Heyee Chem
SKU: HY-1000
Availability: InStock

If you are qualifying a second source for a Mn ≈ 1000 high-density polyethylene wax, this page gives you the numbers side by side and a practical substitution checklist.

1. The short version

HY-1000 is a precisely fractionated low-molecular-weight polyethylene oligomer positioned in the same slot as Mitsui Hi-WAX 100P / HP10A and between Honeywell A-C 8A and A-C 9A in hardness. It is a non-polar, unoxidised, high-crystallinity grade. If your current grade is an unoxidised homopolymer PE wax at Mn ≈ 1000, HY-1000 is a realistic drop-in candidate — subject to the validation steps in section 4.

2. Side-by-side comparison

Property	Heyee HY-1000	Mitsui Hi-WAX 100P / HP10A	Honeywell A-C 8A	Honeywell A-C 9A
Molecular weight	Mn ≈ 1000	Mw 900	—	—
Density (g/cm³)	n/d	0.950	0.93	0.93
Crystallinity	High (low branching)	90%	—	—
Melting point (°C)	≥ 110 (drop)	116	113 (drop point)	115 (drop point)
Congealing point (°C)	≥ 100	121	—	—
Hardness	< 3 dmm @25°C	Penetration 2	1.0 dmm	0.5 dmm
Melt viscosity	> 10 cP @149°C	15 mPa·s @140°C	450 cps	450 cps
Acid value	Nil	Nil	Nil	Nil
Production route	Precisely fractionated PE oligomer	Direct polymerisation (Ziegler)	PE homopolymer	PE homopolymer
Available forms	Prill, flake, micronised	Powder / fine grain (F suffix)	Prill, powder	Prill, powder

Competitor figures are quoted from published technical data sheets for identification and comparison only, and may be revised by their manufacturers. Verify independently before making a substitution decision.

Reading the table correctly. HY-1000's melt viscosity sits close to Hi-WAX 100P (both are very low), which matters most for pigment wetting and lubrication. The A-C 8A/9A grades are quoted at several hundred cps because Honeywell's homopolymer grades in that hardness band are higher-molecular products. If your process depends on the very low viscosity of Hi-WAX 100P, compare against HY-1000 rather than against A-C 8A.

3. What the "precisely fractionated" route changes

Hi-WAX is produced by direct polymerisation over a Ziegler catalyst. HY-1000 is recovered as a precisely fractionated oligomer cut. The practical difference for you:

Narrow molecular-weight distribution — less lot-to-lot drift in melt viscosity and melting point, which is the most common reason for rejecting a second-source wax in appearance-critical applications such as metallic powder coatings and high-loading masterbatch.
Low VOC and low odour — the fractionation step removes light ends. Relevant to automotive interior parts (VOC / odour specifications), food-contact packaging and hygiene products.
High whiteness — HY-1000 is supplied at high whiteness, which is a differentiator in light-colour and metallic-bonded powder coatings, white masterbatch and clear overprint varnishes.

4. Six-step drop-in substitution checklist

Confirm the grade family. Unoxidised homopolymer PE wax only. If you are currently using an oxidised grade (A-C 629/680, Licowax, HY-OPE series), HY-1000 is not a substitute — see PE Wax vs Oxidised PE Wax.
Match the form factor. Prill/flake for melt compounding; micronised D50 5–8 µm for inks and coatings; D50 15–25 µm for masterbatch and rubber chemicals. Request the particle-size distribution, not just the D50.
Run DSC and melt viscosity. Compare melting peak, onset and 140 °C viscosity against your incumbent on the same instrument. Differences under 3 °C and within the viscosity band usually mean no process change is needed.
Bench test at equal loading. For masterbatch: filter pressure rise, colour strength and gloss. For PVC: torque, output rate and surface finish. For powder coatings: degassing behaviour, gloss, and ΔE against your standard panel.
Check the compliance documents. REACH status, RoHS, and — for food contact — the FDA 21 CFR 178.3710 statement. Ask for these before the trial, not after.
Validate three consecutive lots. Batch consistency is the real test of a second source. One good lot proves nothing.

5. Where substitution is straightforward, and where it is not

Application	Substitution outlook	Watch out for
Colour & filler masterbatch	Straightforward; validate colour strength and filter pressure	High inorganic loadings above 60% may prefer a higher-Mn grade
Rigid PVC pipe & profile	Straightforward at equal phr	Plate-out if over-dosed; HY-1000 is an external lubricant only
WPC & PVC foam board	Straightforward	Re-optimise with the stabilizer and filler package
Powder coatings	Straightforward; whiteness is an advantage	Confirm ΔE and degassing on your own panels
Cable compounds	Straightforward; test torque and surface finish	LSZH systems with high ATH/MDH loading need separate validation
Hot-melt adhesives (EVA / APAO)	Usually a partial replacement	PE wax is more brittle than FT wax; blend rather than swap
Printing inks	Requires the micronised grade	Particle-size distribution and dispersibility are critical
Water-based systems	Not applicable	Requires an oxidised grade — use HY-OPE-16 series

6. Supply, packaging and sampling

HY-1000 is produced by Zibo Heyee Fine Chemical Co., Ltd. in Gaoqing County, Zibo, Shandong, with in-house capacity of 60,000 t/a and 500,000 t/a across joint-venture plants. Standard packing is 25 kg bags or 1000 kg jumbo bags, FOB Qingdao. Samples with COA and MSDS ship within 1–3 days.

Request HY-1000 TDS & Free Sample

HY-1000 is supplied as prill, flake or micronized powder (D50 5–8 µm / 15–25 µm) in 25 kg bags or 1000 kg jumbo bags, FOB Qingdao.

Samples ship within 1–3 days with COA & MSDS. Contact brianwang@heyeechem.com or WhatsApp +86-159-4288-5699.

7. FAQ

Is HY-1000 a true drop-in replacement for Hi-WAX 100P?

It is a candidate drop-in for unoxidised homopolymer PE wax at Mn ≈ 1000. The melting point, penetration hardness and melt viscosity should be confirmed against your incumbent on your own instruments, and validated across three consecutive production lots, before switching.

Which Honeywell grade does HY-1000 correspond to?

In hardness it falls between A-C 8A (1.0 dmm) and A-C 9A (0.5 dmm). Note that those grades are quoted at much higher melt viscosity (450 cps at 140 °C) than Hi-WAX 100P, so the closer functional match for low-viscosity applications is Hi-WAX 100P rather than the A-C 8/9 series.

Can HY-1000 replace an oxidised PE wax such as A-C 629 or A-C 680?

No. Oxidised grades carry an acid value of about 15 mg KOH/g, which gives PVC compatibility and emulsifiability. HY-1000 has no acid value and is strictly an external lubricant for non-polar systems.

What is the minimum order quantity for a trial?

Samples start at 1 kg. Commercial supply is 25 kg bags or 1000 kg jumbo bags, FOB Qingdao. Contact brianwang@heyeechem.com for current MOQ and lead time.

Do you provide REACH and FDA documentation?

Yes — REACH status, RoHS, and FDA 21 CFR 178.3710 food-contact statements are available on request. Please specify your target market when you enquire, as documentation requirements differ between the EU, the US and other regions.